Ford F-150 Lug Nut Torque: 150 lb-ft Spec by Generation

An F-150 wheel is heavy and the truck often carries loads or tows, so lug nut torque is not something to guess. Ford’s figure has been the same for two decades on most trucks, and the owner’s manual adds an important re-check rule.

Quick Answer

Ford lists 150 lb-ft (204 N·m) for F-150 wheel nuts with M14 x 1.5 studs on 2015 and newer trucks, and the same 150 lb-ft on 2004-2014 trucks. Ford says to retighten to spec within 100 miles after any wheel disturbance. Most F-150 lug nuts take a 21 mm (13/16 in) socket. Older 1997-2003 trucks with 12 mm studs mostly use 100 lb-ft.

Key Takeaways

  • 2015-2026 F-150 (including Lightning): 150 lb-ft (204 N·m), M14 x 1.5.
  • 2004-2014 F-150: 150 lb-ft.
  • Re-torque within 100 miles after rotation, flat repair or wheel removal.
  • Clean, dry threads; Ford’s figures assume no dirt or rust.

F-150 Lug Nut Torque by Generation

torque wrench on a six-lug pickup truck wheel
Generation Model years Stud size Torque
10th gen (most) 1997-2003 12 mm 100 lb-ft
11th-12th gen 2004-2014 14 mm 150 lb-ft (manuals list 200-204 N·m)
13th gen 2015-2020 M14 x 1.5 150 lb-ft (204 N·m)
14th gen and Lightning 2021-2026 M14 x 1.5 150 lb-ft (204 N·m)

The 2015 F-150 owner’s manual lists 150 lb-ft (204 N·m) for M14 x 1.5 bolts and notes the torque figures are for threads free of dirt and rust. Earlier manuals from 2005 to 2013 also list 150 lb-ft, shown as 200 N·m.

Note: Heavy-duty payload trucks with seven-lug wheels used the same 150 lb-ft figure in Ford’s manuals. Always follow the label or manual for your specific truck.

Products Worth Considering

How to Torque F-150 Lug Nuts

  1. Inspect the wheel pilot hole and mounting surface and remove corrosion or debris, as Ford advises.
  2. Start all six nuts by hand.
  3. Snug them in a star pattern.
  4. Lower the truck so the tire carries weight.
  5. Torque to 150 lb-ft in the star pattern, then repeat.
  6. Retighten to spec within 100 miles.

Warning: Ford warns that corrosion or debris on the wheel mounting surfaces can cause nuts to loosen and the wheel to come off while driving. Clean the surfaces every time.

Socket, Tools and Aftermarket Wheels

Most factory F-150 nuts take a 21 mm (13/16 in) socket. A 1/2-inch drive torque wrench that reaches at least 150 lb-ft is needed. Aftermarket wheels may require a different nut seat; check with the wheel maker. For wheel fitment, see F-150 bolt pattern.

Products Worth Considering

After the Wheels Go Back On

Set pressures to the door label in our F-150 tire pressure guide. If you rotated the tires, the TPMS may need its sensor positions retrained; see F-150 TPMS reset.

Frequently Asked Questions

What is the lug nut torque on a Ford F-150?

Ford lists 150 lb-ft (204 N·m) for F-150 wheel nuts on 2004 and newer trucks, including the Lightning.

What size socket do F-150 lug nuts take?

Most factory F-150 lug nuts take a 21 mm (13/16 in) socket.

When should I re-torque F-150 lug nuts?

Ford says to retighten the nuts to the specified torque within 100 miles after any wheel disturbance.

Is the F-150 Lightning lug nut torque different?

No. The Lightning uses the same M14 x 1.5 studs and 150 lb-ft figure as gas F-150s.

Sources

  1. Ford 2015 F-150 owner’s manual: wheel lug nut torque
  2. Ford 2013 F-150 owner’s manual: wheels and tires
  3. Jim Burke Ford: F-150 lug nut torque by generation
  4. F150gen14 forum: 2022 F-150 socket and thread size

Products Worth Considering

Sharing Is Caring:
About the Author

Cole Mitchell

Cole Mitchell is TubeTyre's Toyota SUV and truck tire specialist, covering the RAV4, Tacoma, 4Runner and Hyundai Sonata in depth. His work focuses on fitment and plus-sizing, tire pressure and rotation schedules, alignment and vibration troubleshooting, and seasonal tire choices for daily drivers. Cole also contributes maintenance, safety and performance guides that explain how tire choice changes handling, braking and ride comfort on the road.

Leave a Comment

Your email address will not be published. Required fields are marked *